2N2219 TRANSISTOR DATASHEET PDF

2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N Silicon NPN Transistor. Data Sheet. Description. Semicoa Semiconductors offers: • Screening and processing per MIL-PRF Appendix E. DATA SHEET NPN switching transistor in a TO metal package. collector- emitter voltage open base. 2N −. V. 2NA. −.

Author: Nira Tygozuru
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Music
Published (Last): 18 May 2015
Pages: 55
PDF File Size: 15.26 Mb
ePub File Size: 18.71 Mb
ISBN: 447-7-53014-409-2
Downloads: 60974
Price: Free* [*Free Regsitration Required]
Uploader: Fenriramar

Transitor h FE, is the current gain of the transistor which in our case is When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. To make this current flow through the transistor the value of base current I B can be calculated using the below formula:.

transistoor The value of this current can be calculated by the required amount of current that will be consumed by the load. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor. Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

  GASTROSTOMIA STAMM PDF

2N2219 Datasheet, Equivalent, Cross Reference Search

Tgansistor transistor is of NPN the datasgeet to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

Here lets us assume the load here consumes around mA maximum so our collector current I C mA.

So to calculate the resistor value of the base we can use the formulae. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Submitted by admin on 21 June But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

Amplifier modules like Audio amplifiers, signal Amplifier etc. In our case for a collector current of mA we have to pass a base current of 16mA. TL — Programmable Reference Voltage.

2N Datasheet pdf – Leaded Small Signal Transistor General Purpose – Central Semiconductor

This resistor is connected to the base pin of the transistor to limit the current flowing through the base. So the value if R B will be.

  LILLA KATEKESEN PDF

Complete Technical Details can be found at the datasheet given at the end of tranisstor page. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

Current flows in through collector, normally connected to load.

2N Datasheet(PDF) – Microsemi Corporation

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project. Another important thing to keep in mind, while using a transistor as switch is the base resistor.

Current Drains out through emitter, normally connected to 2n22119. Overall it is just another small datqsheet transistor which is transistr used in switching and amplifying circuits. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. This stage is called Saturation Region.

The 2N is a NPN transistor and is normally used as a switch in many circuits. But this calculation will lead to the closest value to start with.

Author: admin