User manual for the device Humminbird DX. Online user manual database. User guide • Read online or download PDF • Humminbird DX User Manual • Humminbird Sports and recreation. Humminbird DX Dual Beam DX – read user manual online or download in PDF format. Pages in total:

Author: Taurisar Arasida
Country: Somalia
Language: English (Spanish)
Genre: Career
Published (Last): 18 October 2008
Pages: 58
PDF File Size: 8.74 Mb
ePub File Size: 14.9 Mb
ISBN: 993-8-54563-301-1
Downloads: 96538
Price: Free* [*Free Regsitration Required]
Uploader: Doujas

For Transom Mount transducer installations, install the third mounting screw after the final transducer adjustments. Larger boats or boats with inboard motors crea. Humminbird c Operation Manual Sensitivity.

Pass the cables through the mounting base, out the top of the mounting bracket. On fiberglass hulls, it is best to 1. Your DX conditions over a wide range of temperatures. The Sensitivity function controls the sensitivity of the sonar receiver.

This is important when using the DX in a portable configuration powered by a separate battery, or when powering the unit from a trolling motor battery. The menu appears on-screen while theadjustment is made and times out.

Holding it down longer hummjnbird it into Simulation. Many requests for repair received by Humminbird involve units that do not actually reedrepair.

Check the transducer cable. This allows you todetermine the texture and relative hardness of the bottom. Don’t show me this message again. This applies to Humminbird unitsreturned to our factory in Eufaula, Alabama, and is subject to change without notice. Call Humminbird Customer Support for more information. Otherconnections tested include the boat speed and surface watertemperature sensors. The DX automatically 20dx the level ofreceiver sensitivity based on a number of factors including the depthof the water and the humminblrd of noise present.


Install the control head by sliding it onto the mounting bracket until it is fully seated.

Step Two – Drill the Mounting Holes 1. The upper number ranges available that best matches the depth of the water. Test different locations inthe hull until the optimum performance is achieved.

This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat. The speed input feature only works when the boat is inmotion as the paddle wheel or the speed sensor must rotateto be detected.

Humminbird DX User Manual | 43 pages

Page 23 When the backlight is on the DX will consume more power than with the backlight off. The sound is slightly different for each of the three fish symbol sizes, so with practice, it is possible to distinguish the size of the detected fish without looking at the unit. Humminbird is maanual responsible for over voltage or over current failures.

The depth is measured from the transducer, not necessarily from the surface. The Sensitivity function controls the sensitivity of thesonar receiver. It’s worth a thousand words. The DX automatically selects the appropriate depth range to show the depth of water beneath the transducer.

Humminbird 200DX Dual Beam Operation Manual

Posted on Jan 11, Aug 16, Humminbird Piranhamax Fishfinder. Ensure the mounting area is clear and dry. Step Four – Mount the Transducer to the Transom 1. To print the manual completely, please, download it. If none of these items identifies an obvious problem, thetransducer itself is probably the problem. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Humminbird DX.


The DX is a dual frequency, dual beam unit, and generates two distinct sonar signals – one narrow, one wide. If the unit does not power-up, ensure the unit isfully seated on the mount and that power is available.

Route the cable as far as practical from the VHF radio antenna cables or tachometer cable to reduce the possibility of If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50′ 15 m. Posted by Anonymous on Jun 15, If you are using the DX in Simulator when no transducer is connected, any selected options are lost when the unit is powered off.

Zoom can either operate automatically, in which the Zoom range is constantly adjusted to show the bottom, or manually, in which the user controls the location of the Zoom range. Apply silicone sealant to the mounting holes drilled into the transom. Please assign your manual to a product: Don’t have an account? Inboard boats, wood or metal hulls, and sail boats create unique transducer mounting needs Alternate transducers and mounting methods are detailed below.

Remove the mounting template from the front of the Operations Manual. Step Two – Drill the Mounting Holes1. To remove the unit simply depress the latch on the rear of the unit and lift Figure

Author: admin